
Custom Precision Nylon (PA) CNC Milled Parts
Overview
Custom nylon sliders and guide blocks often require coordinated control of wear-contact faces, guide slots and locating holes. XCM CNC provides CNC milling of PA parts to drawing. Nylon (PA) offers wear resistance, self-lubricating properties and good toughness for components such as sliders, mounting blocks and fixture plates where lower weight and noise are needed. We machine guide faces, slots and locating-hole patterns around the assembly datums so that these features reflect the assembly relationships defined on the drawing. Orders start at one piece. Prototypes typically take 3-7 days, and standard lead times are typically 10-15 days, depending on part complexity and order quantity.

Key Capabilities
- Materials: Nylon (PA), including PA6, PA66 and cast nylon grades; specify the grade for review
- Tolerance: +/-0.005 mm on precision features of parts under 100 mm; +/-0.008 mm on locating holes
- Surface Finish: Milled and finish-milled surfaces; specify the required finish for drawing review
- GD&T: Position and datum relationships for hole groups; CMM inspection available according to drawing requirements
- Max Size: 3-axis machine travel: 3000 x 1600 x 1400 mm; part size depends on stock and setup
- Surface Treatment: Machined finish; other treatment by material and drawing review
- Thread: Internal and external threads according to the drawing and selected PA grade
- Precision Limit: Minimum milled inside corner R0.5 mm; a 40 mm-deep pocket can use R1.0 mm corners, subject to tool access and part geometry

PA Milled Guide Faces and Hole Patterns
We mill flat contact faces, guide slots and locating-hole patterns on Nylon (PA) guide blocks for locating sliders, guide rails and fixture assemblies. Critical dimensions on small precision parts under 100 mm can reach +/-0.005 mm, and locating-hole dimensional tolerances can reach +/-0.008 mm. Specifying datums and inspection conditions on the drawing helps verify the assembly relationships between hole patterns and guide faces.
PA Pocket Corner Radii and Tool Access
PA pocket inside corners can be machined with end mills to a minimum radius of R0.5 mm. A 40 mm-deep pocket can use R1.0 mm inside corners. Appropriate radii provide space for tool entry into the pocket. The machining approach also depends on tool access and part geometry.
PA Thin Wall Milling and Setup
The minimum machinable wall thickness for plastic parts is 1.5 mm. For thin-wall PA milling, the grade, wall geometry and clamping method affect the machining plan. We plan machining and inspection around the wall thickness and functional contact faces specified on the drawing, checking critical dimensions and mounting features after unclamping.
PA Locating Hole Inspection and Fit
Inspection records or CMM reports for PA guide-block locating holes and critical dimensions can be supplied to order, with report scope based on drawing requirements. Specify datums, fits and the delivery inspection condition to help verify the relationships between holes, contact faces and mounting features. If operating humidity affects fit clearance, include those conditions to distinguish delivery dimensional acceptance from operating clearance.
Specifications
| Product Name | Custom Precision Nylon CNC Milled Parts |
|---|---|
| Manufacturer | XCM CNC |
| Factory Location | Shenzhen, Guangdong, China |
| Quality System | ISO 9001, ISO 13485, IATF 16949, GJB9001C |
| Machining Process | CNC milling of flat faces, slots, pockets and locating-hole patterns |
| Material | Nylon (PA) |
| Material Grade | PA6, PA66 or cast nylon; specify grade for review |
| Tolerance | +/-0.005 mm on precision features of parts under 100 mm; +/-0.008 mm on locating holes |
| Surface Treatment | Machined finish; other treatment by material and drawing review |
| Application | Wear sliders, guide blocks, brackets and fixture plates |
| Key Features | Milled guide faces, slot pockets, practical inside corner radii and locating-hole patterns |
| Critical QC Requirements | Identify datums, fit dimensions and delivery inspection state; CMM or dimensional report according to order requirements |
| MOQ | 1 Piece |
| Typical Lead Time | 10-15 business days after drawing review |
| Drawing Formats | STEP, IGS, DWG, PDF, X_T |
Applications
Guide Sliders for Industrial Automation
Typical parts: Guide sliders, wear guide blocks
Sliders move back and forth along guide rails. Nylon (PA)’s wear resistance and self-lubricating properties suit repeated sliding contact. Milling produces flat guide faces, slots and mounting holes. Load and operating humidity affect fit clearance, which should be determined for the operating environment.
Conveyor Guide Strips and Sorting Blocks for Packaging
Typical parts: Conveyor guide strips, sorting blocks
Guide strips constrain product travel along conveyor lines, while sorting blocks withstand repeated contact. PA’s wear resistance and toughness suit these conditions. Milling produces long profiles and mounting-hole patterns. For food-contact applications, specify the grade and applicable compliance requirements.
Test Fixture Plates and Cable Guide Blocks for Electronics
Typical parts: Test fixture plates, cable guide blocks
Fixture plates provide mounting surfaces for test components, while guide blocks organize cable routing. PA’s toughness and properties as an insulating material can inform material selection. Milling produces locating holes, shoulders and cable slots. Specific electrical properties and cleanliness requirements depend on the selected grade and project requirements.
Door Lock Sliders and Assembly Fixture Blocks for Automotive Development
Typical parts: Door lock sliders, assembly fixture blocks
Door lock sliders provide guidance or sliding contact within mechanisms, while fixture blocks locate components during development-stage assembly. PA’s wear and impact resistance make it a candidate for these lightweight parts. Milling produces sliding profiles, locating faces and holes. Select the material grade according to temperature, contact media and actual use.
Why Choose Us
Quality Systems, Machining and Inspection Equipment
XCM CNC has ISO 9001, ISO 13485, IATF 16949 and GJB9001C quality systems, with DMG, Mazak, Matsuura and Brother machining equipment and Hexagon inspection equipment.
Milling and Supporting Operations for Guide Components
For PA sliders and guide blocks located by guide faces, pockets and hole patterns, we can coordinate milling, drilling and sharp-edge removal, with dimensional checks planned around assembly datums.
Equipment Matched to Precision, Quality and Cost Requirements
We match equipment from mainland China, Taiwan, Japan, Europe and the United States to the precision required for PA parts and individual operations, selecting suitable machining resources for guide faces, slots and hole patterns.
Reports Reflecting Slider Mounting Relationships
Critical-dimension inspection, CMM reports and FAI first article reports in your format can be supplied to order. Checks focus on the dimensional relationships between locating holes and guide faces to help you assess the slider’s trial fit.
From Single-Part Trial Fits to Batch Production
Orders start at one piece, with batch production arranged after sample approval. If the guide profile needs adjustment, you can first verify the sample’s contact and mounting relationships with mating components.
FAQ
What inside corner radius should I specify for a milled PA pocket?
End-milled inside corners can reach R0.5 mm. A 40 mm-deep pocket can use R1.0 mm inside corners. Specify the radius with pocket depth and tool-entry space in mind so that the slider or guide block can be machined to suit its actual geometry.
How should I define humidity conditions for a nylon guide slider?
State both the environmental conditions for delivery inspection and the actual operating humidity, as moisture absorption in PA affects operating clearance. Listing fit dimensions, grade and operating environment on the drawing helps us define the acceptance condition.
How thin can a CNC milled nylon wall be?
The minimum machinable wall thickness for plastic parts is 1.5 mm. Thin-wall PA machining also depends on the grade, wall geometry and clamping method. Identify thin-wall areas in the model or drawing.
Which nylon grade should I choose for an impact-loaded slider?
PA6, PA66 and cast nylon can be compared according to impact loads, fit geometry and operating environment. Provide a specific grade or material data sheet. The toughness and dimensional behavior of each grade should be checked against actual requirements.
What tolerances can you machine on PA locating holes?
PA locating-hole dimensional tolerances can reach +/-0.008 mm. Critical dimensions on small precision parts under 100 mm can be controlled to +/-0.005 mm. Specify hole-pattern datums, fit relationships and the delivery inspection condition on the drawing.
How should I specify the finish of a nylon sliding face?
Specify surface requirements for sliding-contact faces and cosmetic faces separately, and identify the critical areas to be checked. There is no single surface roughness value for PA. The target depends on the grade, machining-mark direction and operating contact conditions.
What files are needed for a nylon milling quote?
Provide STEP, IGES, STP, DWG or a dimensioned PDF, and specify the PA grade, quantity, critical tolerances and application requirements. Orders start at one piece. Prototypes typically take 3-7 days, and standard lead times are typically 10-15 days, depending on part complexity and order quantity.
Request a CNC Machining Quote from XCM CNC
Send us your drawings. Our team will review the file and reply with a machining quote. MOQ: 1 piece, with competitive low-cost pricing.



