CNC machining workshop
Custom Nylon (PA) CNC Turning and Milling Parts

Custom Nylon (PA) CNC Turning and Milling Parts

Material: Nylon (PA) MOQ: 1 Piece Tolerance: +/-0.005 mm on precision features of parts under 100 mm; +/-0.008 mm on shaft diameters and locating holes Lead Time: 10-15 business days after drawing review
Email: [email protected] | WhatsApp: +8618638951317

Overview

Nylon hubs and connector sleeves with side holes, flats or keyways require the relationships between cylindrical mating surfaces and lateral mounting features to be controlled. XCM CNC provides Nylon (PA) turning and milling services, coordinating outside-diameter, bore and side-feature machining according to part geometry while drawing on PA’s wear resistance, self-lubricating properties, toughness and potential to reduce weight and noise. Orders start at one piece. Prototypes typically take 3-7 days, and standard lead times are typically 10-15 days, depending on part complexity and order quantity.

custom pa turning and milling parts

Key Capabilities

  • Materials: Nylon (PA), including PA6, PA66 and cast nylon grades; specify the grade for review
  • Tolerance: +/-0.005 mm on precision features of parts under 100 mm; +/-0.008 mm on shaft diameters and locating holes
  • Surface Finish: Turned diameters and milled flats or holes; specify the required finish for drawing review
  • GD&T: Datum relationships between the main bore, turned surfaces and side features; CMM inspection according to drawing requirements
  • Max Size: Turning: up to diameter 1250 x 2000 mm; milling machine travel: 3000 x 1600 x 1400 mm. Combined-part size depends on geometry and setup
  • Surface Treatment: Machined finish; other treatment by material and drawing review
  • Thread: Internal and external threads according to the drawing and selected PA grade
  • Precision Limit: Turn-mill features are planned from the part datums; side-hole and keyway dimensions follow the drawing and inspection method

custom pa turning and milling parts

PA Turned Datums and Milled Side Holes

For PA hubs and connector sleeves, turned bores and outside diameters can serve as primary datums for subsequent side-hole milling. Defining the side-hole position relative to the main-bore datum on the drawing helps verify assembly location requirements between turned and milled features.

PA Hub Flats and Keyway Features

PA drive sleeves and hubs can combine turning and milling to produce cylindrical mating surfaces, flats, slots and keyways. Specify slot width, depth and inspection requirements according to the mating part and keyway standard so that the corresponding assembly features can be checked.

PA Turn-Mill Setup and Feature Relationship

The Mazak i-100S turn-mill center has a second spindle and milling capability for machining cylindrical surfaces, side holes and milled faces on suitable PA parts. Operation sequencing and the use of a combined setup depend on part geometry. Define the datums on the drawing to establish the final positional relationships between machined features.

PA Cross-Hole Deburring and Inspection

Internal cross-hole burrs where the main bore meets a lateral passage can be removed to drawing requirements. Specify the internal burr and cleanliness requirements. CMM and dimensional reports can be supplied to order. Identify hole positions, the main-bore datum and the assembly inspection condition on the drawing to help verify the relationship between the side hole and main bore.

Specifications

Product Name Custom Nylon CNC Turning and Milling Parts
Manufacturer XCM CNC
Factory Location Shenzhen, Guangdong, China
Quality System ISO 9001, ISO 13485, IATF 16949, GJB9001C
Machining Process CNC turning and milling of rotary fits, side holes, flats and keyways
Material Nylon (PA)
Material Grade PA6, PA66 or cast nylon; specify grade for review
Tolerance +/-0.005 mm on precision features of parts under 100 mm; +/-0.008 mm on shaft diameters and locating holes
Surface Treatment Machined finish; other treatment by material and drawing review
Application Hubs, connector sleeves, drive sleeves and roller components
Key Features Turned bore and outside diameter related to milled side holes, flats or keyways
Critical QC Requirements Define bore datum, side-feature position and internal burr requirements; CMM or dimensional report according to order requirements
MOQ 1 Piece
Typical Lead Time 10-15 business days after drawing review
Drawing Formats STEP, IGS, DWG, PDF, X_T

Applications

Drive Sleeves and Hubs for Automation

Typical parts: Keyed drive sleeves, flat-sided hubs

Drive sleeves and hubs connect rotating components to shafts. PA’s wear resistance, self-lubricating properties and potential to reduce weight and noise suit some low-load drive designs. Turning produces bores, outside diameters and end faces, followed by milling of keyways or flats. The fit design should consider torque, load and humidity.

Side-Drilled Rollers and Guide Sleeves for Conveying and Packaging

Typical parts: Side-drilled rollers, guide sleeves

Rollers and guide sleeves provide support or guidance along conveying paths. PA’s wear resistance and toughness suit repeated contact. After turning the profile and center bore, lateral mounting holes can be milled and drilled. For food-contact applications, specify the grade and applicable documentation requirements.

Connector Housings and Cable Sleeves for Electronic Equipment

Typical parts: Connector housings, cable sleeves

Housings and sleeves protect connections and provide mounting interfaces. PA’s toughness and properties as an insulating material can guide material selection. Turn-mill machining produces circular interfaces, end-face shoulders and mounting flats. Dielectric, flame-retardancy and sealing requirements should each be defined according to the grade and drawing.

Sensor Housings and Pipe Fitting Prototypes for Automotive Development

Typical parts: Side-port sensor housings, prototype pipe fittings

These prototypes help check the structural fit of circular interfaces, lateral connections and mounting faces. PA’s toughness and low weight support development-stage trial assembly. Turning and side-hole milling or drilling can be combined to produce interfaces and mounting features. Material suitability depends on temperature, media and actual use. For pressure-bearing or media-contact applications, provide the pressure specifications, media type and operating conditions with your inquiry so that the material and machining approach can be assessed.

Why Choose Us

Quality Systems, Machining and Inspection Equipment

XCM CNC has ISO 9001, ISO 13485, IATF 16949 and GJB9001C quality systems, with DMG, Mazak, Matsuura and Brother machining equipment and Hexagon inspection equipment.

Coordinated Turning, Milling and Side-Feature Machining

From small connector components to large structural parts, we can coordinate turning, milling, drilling and cross-hole deburring to drawing for PA parts with cylindrical mating surfaces and lateral mounting features.

Equipment Matched to Precision, Quality and Cost Requirements

We match equipment from mainland China, Taiwan, Japan, Europe and the United States to the precision required at each PA machining stage, selecting suitable machining resources for circular interfaces, side holes and flats.

First Article Reports for Hole-Position Relationships

CMM, critical-dimension inspection and FAI first article reports in your format can be supplied to order. We check the side-hole position and mounting orientation relative to the main-bore datum against the drawing to help you assess the connector’s assembly relationships.

Cross-Hole Cleaning Requirements Included in Delivery Preparation

Cross-hole exits can be treated to meet the internal burr and cleanliness requirements specified on the drawing, and assembly edges can be deburred. Identify the main bore, side holes and cleanliness acceptance requirements together on the drawing.

FAQ

Can a nylon sleeve include side holes and milled flats?

Yes. Suitable PA geometries can combine turned cylindrical surfaces with milled side holes, flats or keyways. Specify how these lateral features relate to the main bore and end-face datums on your drawing.

Which datum should relate a side hole to the main bore?

The drawing should generally identify the main-bore axis as the datum for side-hole position and define an end-face or angular locating datum. This allows inspection requirements to reflect the connector’s actual mounting orientation and position.

When is a turn-mill center useful for a PA connector?

When a part includes turned outside diameters or bores as well as milled or drilled features such as side holes and flats, turn-mill equipment can be used to plan the related machining. Whether to combine operations depends on part geometry and datum requirements.

How should I specify a keyway on a nylon drive sleeve?

Specify keyway width, depth, length and the applicable standard, and define its locating relationship to the bore or axis. Keyway machining and inspection plans depend on the PA grade and drawing requirements.

How are burrs controlled where a side hole meets a nylon bore?

Cross-hole exits can be treated to the internal burr and cleanliness requirements specified on the drawing. Identify where the main bore and side hole intersect, the acceptable edge condition and whether internal cleanliness needs inspection.

How does moisture affect the fit of a nylon connector?

Moisture absorption in PA affects fit dimensions in use, so distinguish delivery inspection dimensions from fit requirements under operating conditions. Provide the grade, operating humidity and assembly clearance requirements to help define acceptance conditions.

What information is needed to quote a turned and milled PA part?

Provide STEP, IGES, STP, DWG or a dimensioned PDF, and specify the PA grade, quantity, critical tolerances, main-bore datum and application requirements. Orders start at one piece. Prototypes typically take 3-7 days, and standard lead times are typically 10-15 days, depending on complexity and order quantity.

Certified Quality ISO 9001 | ISO 13485 | GJB9001C | IATF:16949 View Quality Control & Inspection Proof

Request a CNC Machining Quote from XCM CNC

Send us your drawings. Our team will review the file and reply with a machining quote. MOQ: 1 piece, with competitive low-cost pricing.

Contact Form Demo 2

STEP, IGS, STL, DWG, DXF, PDF, JPG or ZIP. Max. 50 MB. Multiple or large files? Email: [email protected]

You May Also Like