
Custom Precision PEEK CNC Milled Parts
Overview
XCM CNC mills precision PEEK parts in Shenzhen, including cavities, steps, mounting faces and locating-hole patterns. PEEK may suit structures that require temperature and chemical resistance with relatively high rigidity; performance depends on the specified grade and service conditions. Precision features are machined on DMG, Mazak and other equipment. The factory holds ISO 9001, ISO 13485, IATF 16949 and GJB9001C certifications. MOQ is one piece. Prototypes typically take 3-7 days and standard orders 10-15 days, subject to complexity and quantity.

Key Capabilities
Precision features on PEEK milled parts can be held to +/-0.005 mm, while locating holes and shaft diameters can be held to +/-0.008 mm. The capabilities below identify where each value applies.
- Materials: PEEK, including unfilled, glass-filled, carbon-filled and wear-modified grades specified by drawing
- Tolerance: +/-0.005 mm on precision features; +/-0.008 mm for shaft diameters and locating holes
- Surface Finish: Milled mounting faces, cavity floors and contact surfaces; finish requirements depend on PEEK grade and function, confirmed by order
- GD&T: Position, flatness and profile defined by drawing datums; verified on Hexagon CMM and WanHao VMS-3020G 2.5D video measuring machine
- Max Size: 3-axis travel 3000 x 1600 x 1400 mm; 5-axis (DMG 80mono) 800 x 600 x 900 mm; multi-face single setup up to 600 x 1200 x 500 mm
- Surface Treatment: Deburring; other treatment requirements reviewed for PEEK grade and drawing
- Thread: M2 to M220; NPT / BSP / G / PT pipe threads; go/no-go gauge inspection
- Precision Limit: +/-0.005 mm on precision features; +/-0.008 mm locating-hole size; min. milled hole 0.3 mm; min. plastic wall 1.5 mm (specific features, by drawing review)

PEEK CNC Milling Tolerance for Cavities and Mounting Faces
PEEK cavities, steps and mounting faces can have specified precision features held to +/-0.005 mm; this is not a blanket tolerance for the whole part. We aim to mill cavities and mounting faces in one setup. Multi-face machining in one setup accommodates parts up to 600 x 1200 x 500 mm and reduces datum shifts from reclamping.
Precision PEEK Locating Hole Machining
PEEK locating-hole diameters can be held to +/-0.008 mm. The minimum milled hole is 0.3 mm and the minimum drilled hole is 0.2 mm. Hole position and diameter are separate requirements. Specify datums and positional tolerances on the drawing so CMM inspection can evaluate the assembly interface.
PEEK Deep Pocket Milling and Thin-Wall Limits
A typical PEEK pocket has a depth-to-width ratio of 4:1, or up to 5:1 with extended tooling. The minimum plastic wall is 1.5 mm. Because PEEK dissipates heat poorly, deep pockets are generally machined in layers and finish milled after releasing clamping pressure to reduce distortion and residual stress. For a 40 mm deep cavity, an inside corner radius of at least R1.0 mm is recommended; R0.5 mm is the usual end-mill corner limit.
PEEK Milled Part Inspection Equipment
Hole-pattern position and profile are measured on a Hexagon Inspector Classic 06.08.06 CMM. A WanHao VMS-3020G 2.5D vision measuring machine provides noncontact checks of planar hole positions and cavity profiles. A TRIMOS 600L height gauge checks steps and cavity depth, including height features at the +/-0.005 mm level. CMM and first article inspection (FAI) reports can be supplied in the customer’s format.
Specifications
| Product Name | Custom Precision PEEK CNC Milled Parts |
|---|---|
| Manufacturer | XCM CNC (Shenzhen Xinchuangmeng Co., Ltd) |
| Factory Location | Shenzhen, China |
| Quality System | ISO 9001, ISO 13485, IATF 16949, GJB9001C |
| Machining Process | CNC milling (3-axis, 3+2-axis, 5-axis) |
| Material | PEEK |
| Material Grade | Unfilled, glass-filled, carbon-filled or wear-modified grade as specified by drawing |
| Tolerance | +/-0.005 mm on precision features; +/-0.008 mm for shaft diameters and locating holes |
| Surface Treatment | Deburring; other treatment by PEEK grade and drawing review |
| Max Part Size | 3-axis 3000 x 1600 x 1400 mm; 5-axis 800 x 600 x 900 mm |
| Inspection | Dimensional inspection, CMM and FAI reports by order; equipment: Hexagon Inspector Classic 06.08.06, WanHao Rational VMS-3020G, TRIMOS 600L Height Gauge |
| Application | PEEK housings, instrument flow blocks, test fixtures and automation bases |
| Key Features | Milled cavities, mounting faces, steps and locating-hole patterns; precision features +/-0.005 mm; locating-hole size +/-0.008 mm |
| Critical QC Requirements | Define mounting datums, cavity depth and hole position separately; dimensional, CMM or FAI report scope by order; surface finish: Milled contact and mounting faces; finish requirements depend on PEEK grade and function |
| MOQ | 1 piece |
| Typical Lead Time | Prototype 3-7 days; standard 10-15 days depending on complexity and quantity |
| Drawing Formats | STEP, IGES, STP, DWG, PDF with dimensions |
Applications
Analytical instrument fluid manifolds and sample cells
Typical parts: Fluid manifold, sample cell holder
PEEK grades for fluid-contact parts can be selected according to the chemical medium. Milling the cavity, interface mounting faces and hole pattern in one part keeps the fluid connections aligned with the equipment datums. Specify the medium, temperature and cleaning requirements on the drawing. Leak testing is not included in the standard service.
Relevant capabilities: Minimum milled hole 0.3 mm, deep holes up to L/D = 10, cross-hole deburring.
Electronic test sockets and soldering fixtures
Typical parts: High-temperature test socket, soldering fixture
PEEK grades for test and soldering fixtures can be selected for the thermal environment and insulation requirements. Milling forms component locating holes, steps and mounting planes. Hole patterns and fixture datums follow the drawing. Electrical insulation or static-control properties depend on the selected grade’s data.
Relevant capabilities: Locating holes +/-0.008 mm; VMS-3020G vision inspection of hole arrays.
Industrial automation sensor bases and guide blocks
Typical parts: Sensor mounting base, guide block
PEEK can be considered as an alternative to metal for mounting components that face heat or specified media. Milling produces planar datums, counterbores and locating-hole patterns for sensor mounts and linear guide blocks assembled from several sides. Actual loads and wear life depend on the operating conditions.
Relevant capabilities: Multi-face machining in one setup up to 600 x 1200 x 500 mm; threads from M2.
Medical instrument guides and accessory mounts
Typical parts: Surgical guide, instrument accessory mount
PEEK can be evaluated for lightweight instrument accessories with complex profiles. Milling can produce guide faces, holes and mounting datums. The customer determines material grade, contact type, cleaning and sterilization requirements from the drawing and applicable regulations. The material name alone does not establish finished-device suitability.
Relevant capabilities: ISO 13485 quality system, 5-axis contour machining, Hexagon CMM reports.
Chemical equipment valve manifold mounting plates
Typical parts: Valve manifold mounting plate, pump end plate
Where media contact or insulation affects material selection, PEEK milled parts can be assessed against the specified medium. Machining mounting faces, valve holes and connecting-hole patterns together relates the pipe connections to equipment mounting positions. Pocket depth and thin walls are planned around the particular geometry.
Relevant capabilities: 3-axis travel 3000 x 1600 x 1400 mm; NPT / BSP / G pipe threads.
Why Choose Us
Quality systems and machining equipment
We operate under ISO 9001, ISO 13485, IATF 16949 and GJB9001C quality systems. DMG, Mazak, Matsuura and Brother machines, together with dimensional inspection equipment, support machining and verification of PEEK cavity plates.
Cavities, mounting faces and holes planned together
We plan milling and dimensional checks around related cavities, steps, mounting faces and locating-hole patterns. This helps verify pocket depth and assembly interfaces. Hole diameter, position and datums are defined separately on the drawing.
Tiered equipment strategy for cost-controlled machining
XCM CNC has four tiers of CNC equipment from mainland China, Taiwan, Japan, Europe and the United States. We assign operations with less demanding tolerances to domestic or Taiwanese machines and precision work to imported machines such as DMG and Mazak. Matching machines to actual tolerance needs controls machining cost while meeting the drawing.
Manufacturability review before quoting
Before quoting, our engineers flag pocket depth, inside corners and thin walls that may affect cost or lead time, and suggest changes. You can decide whether to revise or retain the design before ordering, reducing rework during prototyping.
Prototype approval, production and drawing confidentiality
New projects begin with a prototype and proceed to batch production after approval. Production follows the approved first article’s process and inspection items. Drawings and models can be submitted after an NDA is signed; material certificates and report formats are agreed in the order.
FAQ
What tolerances apply to PEEK cavities and locating holes?
Specified precision features can be held to +/-0.005 mm, and locating-hole diameters to +/-0.008 mm. Positional tolerances and datum relationships must be called out separately on the drawing; they cannot be inferred from the hole-size tolerance.
How do pocket depth and wall thickness limit PEEK milling?
A typical PEEK pocket has a 4:1 depth-to-width ratio, and the minimum plastic wall is 1.5 mm. Deeper pockets require longer tool reach and a correspondingly larger inside corner radius. Show pocket depth, corner radii and wall thickness on the drawing so we can assess tool access and clamping.
How does PEEK grade affect milled surfaces?
The surface of a filled PEEK grade depends on the grade and feature; it cannot be assumed to be better or worse. There is no universal default Ra for PEEK. Specify the grade and contact-surface requirements on the drawing, along with any cleaning or leak-validation requirements.
Can I order a single PEEK prototype, and how long does it take?
Yes. MOQ is one piece. Prototypes typically take 3-7 days, and standard production orders 10-15 days, depending on complexity and quantity. The customer approves the prototype before batch production.
What payment, shipping and packaging options are available?
We accept T/T, PayPal and Western Union. Shipping options include DHL, FedEx, UPS and sea freight. PEEK parts are normally packed with foam in cartons; wooden cases can be used for larger or batch orders.
What files are needed for a confidential PEEK milling quote?
Provide 2D/3D drawings, the specified PEEK grade, quantity, tolerances and intended use. We accept STEP, IGES, STP, DWG or dimensioned PDF files. An NDA can be signed before you send the drawings.
Request a CNC Machining Quote from XCM CNC
Send us your drawings. Our team will review the file and reply with a machining quote. MOQ: 1 piece, with competitive low-cost pricing.



