
Custom Precision PEEK 5-Axis Machined Parts
Overview
Five-axis machining allows angled holes, undercuts and multi-directional mounting faces on contoured PEEK parts to be produced with fewer setups. XCM CNC uses a DMG 80mono 5-axis machine and Matsuura machining centers for these complex parts. The factory holds ISO 9001, ISO 13485, IATF 16949 and GJB9001C certifications. PEEK’s rigidity, temperature resistance and chemical resistance can inform material selection, subject to the grade and operating conditions. MOQ is one piece. Prototypes typically take 3-7 days and standard orders 10-15 days, depending on complexity and quantity.

Key Capabilities
Capability for 5-axis PEEK parts depends on the machining envelope, tool approach and inspection method. The parameters below define the scope of each capability.
- Materials: PEEK, including unfilled, glass-filled, carbon-filled and wear-modified grades specified by drawing
- Tolerance: +/-0.005 mm on precision features; +/-0.008 mm for shaft diameters and locating holes
- Surface Finish: Contoured, grip and mounting surfaces specified separately; finish and appearance requirements depend on PEEK grade and function, confirmed by order
- GD&T: Profile, position and angular relationships defined by drawing datums; verified by Hexagon CMM, 3D scan or profile inspection
- Max Size: 5-axis 800 x 600 x 900 mm (DMG 80mono); multi-face single setup up to 600 x 1200 x 500 mm; 3-axis travel 3000 x 1600 x 1400 mm
- Surface Treatment: Deburring; other treatment requirements reviewed for PEEK grade and drawing
- Thread: M2 to M220; NPT / BSP / G / PT pipe threads; go/no-go gauge inspection
- Precision Limit: +/-0.005 mm on precision features; countersink angle 90 degrees +/-0.1 degrees; min. plastic wall 1.5 mm; surface profile defined separately (specific features, by drawing review)

PEEK 5-Axis Contour Machining: Simultaneous vs 3+2
Contoured PEEK parts can be machined with 3-axis, 3+2 positioning or simultaneous 5-axis methods. The DMG 80mono 5-axis machining envelope is 800 x 600 x 900 mm. For parts with only angled holes or several sloped faces, 3+2 positioning is often enough. Continuous freeform surfaces, such as handle grip faces, may call for simultaneous 5-axis machining. Specified precision features can be held to +/-0.005 mm.
PEEK Multi-Face Machining in a Single Setup
PEEK multi-face parts up to 600 x 1200 x 500 mm can be machined in one setup, with holes and mounting faces on five sides referenced to one datum. Each additional setup can introduce clamping distortion and alignment error, so locating holes across faces are preferably machined together. Hole diameters can be held to +/-0.008 mm. Fixtures consume part of the machine envelope, so orientation must be assessed from the CAD model.
PEEK Angled Holes, Countersinks and Undercuts
Angled locating holes in PEEK can be machined to +/-0.008 mm diameter tolerance, and a 90-degree countersink can have an angle tolerance of +/-0.1 degree. Tilting the 5-axis spindle allows the tool to approach an inclined face normally, reducing drill wander. Undercuts can also be machined; whether they require additional setups or special tools depends on obstruction and access.
PEEK Contoured Part Inspection Against CAD
A Hexagon Inspector Classic 06.08.06 CMM measures contoured PEEK parts against the CAD model. Freeform surfaces can also receive 3D scanning or profile inspection. The +/-0.005 mm tolerance applies only to specified precision features, not automatically to the surface profile. Profile inspection can verify a 90-degree countersink angle to +/-0.1 degree. Third-party inspection reports are available when requested.
Specifications
| Product Name | Custom Precision PEEK 5-Axis Machined Parts |
|---|---|
| Manufacturer | XCM CNC (Shenzhen Xinchuangmeng Co., Ltd) |
| Factory Location | Shenzhen, China |
| Quality System | ISO 9001, ISO 13485, IATF 16949, GJB9001C |
| Machining Process | 5-axis CNC machining (simultaneous and 3+2) |
| Material | PEEK |
| Material Grade | Unfilled, glass-filled, carbon-filled or wear-modified grade as specified by drawing |
| Tolerance | +/-0.005 mm on precision features; +/-0.008 mm for locating holes |
| Surface Treatment | Deburring; other treatment by PEEK grade and drawing review |
| Max Part Size | 5-axis 800 x 600 x 900 mm; multi-face single setup 600 x 1200 x 500 mm |
| Inspection | Dimensional inspection, CMM, 3D scanning or profile reports by order; third-party report available; equipment: Hexagon Inspector Classic 06.08.06, WanHao Rational VMS-3020G, TRIMOS 600L Height Gauge |
| Application | PEEK contoured instrument parts, multi-angle fixtures, grippers and mounting brackets |
| Key Features | Contoured surfaces, angled holes, multi-directional mounting faces and restricted tool access; 5-axis machining size 800 x 600 x 900 mm subject to fixture and orientation |
| Critical QC Requirements | Specify precision dimensions, surface profile and hole position separately; select CMM, 3D scan or profile inspection by drawing; surface finish: Contoured and mounting surfaces specified separately; requirements depend on PEEK grade and function |
| MOQ | 1 piece |
| Typical Lead Time | Prototype 3-7 days; standard 10-15 days depending on complexity and quantity |
| Drawing Formats | STEP, IGES, STP, DWG, PDF with dimensions |
Applications
Medical instrument handles and multi-angle guides
Typical parts: Instrument handle, angled guide
PEEK can be evaluated when instrument components need complex hand-contact contours or lightweight guide structures. Five-axis machining places mounting faces and guide holes in several directions along the contour. The customer determines grade, contact, cleaning and sterilization requirements from the drawing and applicable regulations.
Relevant capabilities: Simultaneous 5-axis freeform machining; ISO 13485 quality system.
Industrial automation contoured grippers and sensor brackets
Typical parts: Custom end-effector gripper, angled sensor bracket
Where gripping surfaces or sensor interfaces face different directions, PEEK can be assessed as a lightweight material against load and temperature requirements. Five-axis machining places multi-directional holes and mounting faces on matching contours. Load capacity and service life depend on part design and operating conditions.
Relevant capabilities: Multi-face machining in one setup up to 600 x 1200 x 500 mm; locating holes +/-0.008 mm.
Analytical instrument contoured sample cells and fluid manifolds
Typical parts: Contoured sample cell, angled fluid manifold
PEEK can be evaluated for chemical resistance against the contact medium. Five-axis machining connects angled ports, contoured exteriors and mounting datums in different directions. Internal-channel access, medium, cleaning and leak-testing requirements should be specified separately.
Relevant capabilities: Normal tool entry for angled holes; cross-hole deburring.
Aerospace equipment contoured brackets and cable clamps
Typical parts: Contoured mounting bracket, multi-angle cable clamp
PEEK can be assessed by specified grade and environment where equipment accessories need lower weight or chemical resistance. Five-axis machining produces contoured mounting profiles and angled fixing holes. The customer determines aerospace suitability against drawings and airworthiness requirements; material properties alone do not constitute aerospace approval or finished-part qualification.
Relevant capabilities: GJB9001C quality system; CMM inspection against CAD.
Instrument multi-face mounts and angled interface blocks
Typical parts: Multi-face mount, angled interface block
Where instrument interfaces must clear nearby structures or occupy several planes, PEEK’s chemical resistance and insulation can be assessed against the environment. Five-axis machining handles holes, slots and datum faces at different angles. Define how contour profiles and dimensions across faces are inspected on the drawing.
Relevant capabilities: 90-degree countersinks +/-0.1 degree; 3+2 positioning.
Why Choose Us
Quality systems and 5-axis equipment
We machine under ISO 9001, ISO 13485, IATF 16949 and GJB9001C quality systems. DMG, Mazak, Matsuura and Brother equipment, along with inspection tools for complex parts, support PEEK contours and multi-directional features.
Process selected by contour and tool access
We review the CAD model for access to contours, angled holes and multi-face interfaces before choosing 3+2 or 5-axis machining. A side hole alone does not necessarily require 5-axis machining.
Tiered equipment strategy for cost-controlled machining
XCM CNC has four tiers of CNC equipment from mainland China, Taiwan, Japan, Europe and the United States. Planar surfaces and simple holes go to domestic or Taiwanese machines; contours and precision features go to imported equipment such as DMG and Mazak. Machine selection follows actual precision needs so 3-axis work does not occupy a 5-axis machine, controlling cost while meeting the drawing.
Visible contours accepted to customer standards
Visible contours on handles and housings can be accepted to a customer-supplied appearance standard or sample. We agree in advance how scratches, tool marks and color variation will be judged, reducing disputes on receipt.
Separate prototype and production schedules
Complex contoured prototypes typically take 3-7 days, allowing assembly validation first. Batch production is scheduled after prototype approval, with a standard lead time of 10-15 days, so project milestones can be planned in advance.
FAQ
When does a contoured PEEK part need 5-axis machining?
Consider 5-axis or 3+2 machining when contours, angled holes or undercuts need access from several directions. A side hole alone may not require 5-axis machining. Some undercuts cannot be completed in one setup even with five axes; the 3D model determines the approach.
Does the precision-feature tolerance also apply to a PEEK surface profile?
No. The +/-0.005 mm tolerance applies to specified precision features. Define surface-profile tolerance separately on the drawing. A locating-hole diameter can be assessed to +/-0.008 mm, which likewise does not replace a profile requirement.
Can you machine PEEK parts larger than the 5-axis envelope?
Yes, depending on geometry. Parts exceeding 800 x 600 x 900 mm can move to 3-axis equipment with 3000 x 1600 x 1400 mm travel and be machined in multiple setups. Large parts with many angled features need an advance workholding review.
Do I need to send a 3D model for a 5-axis PEEK quote?
Yes. Freeform-surface programming and inspection depend on a 3D model, so provide STEP, IGES or STP. Use 2D drawings in DWG or dimensioned PDF to specify tolerances and datums.
Can you provide a third-party inspection report for contoured PEEK parts?
Yes. A dimensional inspection report is standard. Request CMM or 3D scan reports when ordering. For a third-party inspection report, identify the inspection items early so it can be scheduled.
Can I prototype the same part in several PEEK grades in one order?
Yes. MOQ is one piece. Several prototypes of the same part can be made in unfilled, glass-filled or carbon-filled PEEK. Prototypes typically take 3-7 days, and the grade variants can be delivered together for comparison testing.
What payment, shipping and packaging options are available?
We accept T/T, PayPal and Western Union. Shipping options include DHL, FedEx, UPS and sea freight. Parts are packed with foam in cartons or wooden cases as required.
Request a CNC Machining Quote from XCM CNC
Send us your drawings. Our team will review the file and reply with a machining quote. MOQ: 1 piece, with competitive low-cost pricing.



