
Custom Precision PEEK CNC Turned Parts
Overview
Bushings, sleeves and sealing rings are common PEEK turned parts. Their bores, outside diameters and end faces provide guidance or location in an assembly. XCM CNC makes these rotary parts on Mazak turn-mill centers and automatic lathes. Shaft diameters can be held to +/-0.008 mm and specified precision features to +/-0.005 mm. The factory holds ISO 9001, ISO 13485, IATF 16949 and GJB9001C certifications. PEEK’s temperature and chemical resistance can guide selection, but suitability depends on the grade, fit clearance and operating environment. MOQ is one piece. Prototypes typically take 3-7 days and standard orders 10-15 days.

Key Capabilities
PEEK turning capacity ranges from small bushings to large rings up to diameter 1250 mm. The parameters below show where each capability applies.
- Materials: PEEK, including unfilled, glass-filled, carbon-filled and wear-modified grades specified by drawing
- Tolerance: +/-0.005 mm on precision features; +/-0.008 mm for shaft diameters and locating holes
- Surface Finish: Turned bores, outside diameters and seal lands; finish requirements depend on PEEK grade and function, confirmed by order
- GD&T: Coaxiality and runout referenced to rotary datums; verified on Hexagon CMM and TRIMOS 600L height gauge
- Max Size: Turning diameter 1250 mm at 2000 mm length (diameter 1200 mm conservative); max bore diameter 1000 mm
- Surface Treatment: Deburring; other treatment requirements reviewed for PEEK grade and drawing
- Thread: M2 to M220; NPT / BSP / G / PT pipe threads; go/no-go gauge inspection
- Precision Limit: +/-0.005 mm on precision features; +/-0.008 mm shaft diameter; min. plastic wall 1.5 mm; chamfer C0.1-C3.0 mm (specific features, by drawing review)

PEEK Bushing Bore and Outside Diameter Tolerance
The outside diameter of a PEEK bushing can be held to +/-0.008 mm, while a drawing-specified precision bore or mating surface can be held to +/-0.005 mm. We aim to turn the bore and outside diameter in one setup to preserve their coaxial relationship. These are size tolerances, not h6 or H7 fit classes.
PEEK Thin-Wall Ring Turning and Clamping
The minimum wall thickness for PEEK rings is 1.5 mm, and outside-diameter tolerance is assessed at +/-0.008 mm. Direct three-jaw clamping can make a thin ring oval, so finish turning generally uses enveloping soft jaws or axial face clamping. Dimensions are measured in the free state after unclamping; specify the measurement condition on the drawing.
PEEK Turned Edge, Chamfer and Knurl Details
Chamfers on PEEK rotary parts range from C0.1 to C3.0 mm, the minimum external corner radius is R0.2 mm, and sharp edges are removed by 0.1 mm. Straight or diamond knurling with module 0.3-1.0 can be used on instrument handles and knobs. Specify chamfers or radii separately at sealing support ring end-face edges to avoid damaging seals during assembly.
Large-Diameter PEEK Ring Turning Capacity
Large PEEK rings and end caps are turned on a Shenyang CK61125X2000 CNC lathe. The conservative turning diameter is 1200 mm, and the maximum bored diameter is 1000 mm. Turning allowance and clamping locations for large rings must be planned around the blank. A TRIMOS 600L height gauge rechecks step height and end-face position.
Specifications
| Product Name | Custom Precision PEEK CNC Turned Parts |
|---|---|
| Manufacturer | XCM CNC (Shenzhen Xinchuangmeng Co., Ltd) |
| Factory Location | Shenzhen, China |
| Quality System | ISO 9001, ISO 13485, IATF 16949, GJB9001C |
| Machining Process | CNC turning |
| Material | PEEK |
| Material Grade | Unfilled, glass-filled, carbon-filled or wear-modified grade as specified by drawing |
| Tolerance | +/-0.005 mm on precision features; +/-0.008 mm for shaft diameters |
| Surface Treatment | Deburring; other treatment by PEEK grade and drawing review |
| Max Part Size | Turning diameter 1250 x 2000 mm (diameter 1200 mm conservative); max bore 1000 mm |
| Inspection | Dimensional inspection report; CMM and FAI reports by order; key-dimension 100% inspection available; equipment: Hexagon Inspector Classic 06.08.06, WanHao Rational VMS-3020G, TRIMOS 600L Height Gauge |
| Application | PEEK bushings, sleeves, valve seats and instrument rings |
| Key Features | Turned bores, outside diameters, shoulders, end faces and grooves; shaft diameters +/-0.008 mm; specified precision features +/-0.005 mm; threads: M2-M220; NPT / BSP / G / PT |
| Critical QC Requirements | Define bore, outside diameter, length and rotary datums separately; CMM or FAI report scope by order; surface finish: Turned bores, outside diameters and seal lands; requirements depend on PEEK grade and function |
| MOQ | 1 piece |
| Typical Lead Time | Prototype 3-7 days; standard 10-15 days depending on complexity and quantity |
| Drawing Formats | STEP, IGES, STP, DWG, PDF with dimensions |
Applications
Industrial automation guide bushings and sleeves
Typical parts: Guide bushing, sliding sleeve
A PEEK grade can be evaluated for reciprocating guides according to load, speed and fit clearance as an alternative to some metal bushings. Turning forms the bore, outside diameter, end face and ring groove to control the shaft-to-bore fit and installed length. Service life depends on actual operating conditions.
Relevant capabilities: Outside diameter +/-0.008 mm; small-part batch machining on Jingshang 80 automatic lathes.
Analytical instrument valve seats and pump bushings
Typical parts: Valve seat, pump bushing
PEEK for chemical-contact valve seats or pump bushings can be chosen according to medium and temperature. Turning produces sealing end faces, bores and stepped outside diameters. Define sealing-surface, clearance and leak-validation requirements separately.
Relevant capabilities: Precision features +/-0.005 mm; sharp-edge removal of 0.1 mm on end faces.
Electronic connector insulating sleeves and spacers
Typical parts: Connector insulating sleeve, cylindrical spacer
A PEEK grade can be selected for cylindrical electrical isolation structures according to the insulation target. Turning produces coaxial bores, outside diameters and end-face steps for sleeves and spacers inside connector housings. High-frequency performance depends on the selected grade data.
Relevant capabilities: Chamfers from C0.1 mm; WanHao VMS-3020G vision inspection of small parts.
Medical instrument sleeves and cylindrical handles
Typical parts: Endoscope sleeve, cylindrical instrument handle
PEEK can be assessed where instrument components need temperature resistance or lightweight cylindrical construction. Turning forms sleeve bores, outside diameters, end faces and threaded interfaces. The customer determines material grade, contact, sterilization and cleaning requirements from the drawing and applicable regulations.
Relevant capabilities: ISO 13485 quality system; knurl module 0.3-1.0.
Rotating equipment sealing rings and retaining rings
Typical parts: Seal support ring, shaft retaining ring
PEEK for rotary seal supports requiring chemical resistance can be assessed against the medium, temperature and fit conditions. Turning the inner and outer diameters, end faces and ring grooves aligns sealing edges and axial mounting positions. Operating clearance depends on the service environment.
Relevant capabilities: Large-ring turning to diameter 1200 mm; minimum wall thickness 1.5 mm.
Why Choose Us
Quality systems and machining equipment
We machine under ISO 9001, ISO 13485, IATF 16949 and GJB9001C quality systems. DMG, Mazak, Matsuura and Brother machines and dimensional inspection equipment support production and inspection of PEEK rotary parts.
Bores, diameters, shoulders and faces planned around the fit
When turning sleeves, we machine bores, outside diameters, shoulders and end faces to the drawing, with ring grooves and threads as needed. Separately defining fit dimensions, axial lengths and rotary datums helps verify the assembly relationship.
Tiered equipment strategy for cost-controlled machining
XCM CNC has four tiers of CNC equipment from mainland China, Taiwan, Japan, Europe and the United States. Standard diameter and end-face turning goes to domestic or Taiwanese machines, while precision mating surfaces go to imported equipment such as DMG and Mazak. Matching machines to actual precision requirements controls cost while meeting the drawing.
Full inspection of critical fit dimensions in batch orders
Batch orders for bushings and sealing rings can receive 100% inspection of critical mating dimensions and appearance, rather than sample checks alone. Every part then goes through the same inspection items, reducing selection work on the assembly line.
Batch material certificates and grade traceability
Each PEEK batch can be supplied with a material certificate, and an SGS environmental report can be provided when needed. The finished parts can thus be traced to the PEEK grade and material batch during incoming review.
FAQ
What tolerance can you hold on a PEEK shaft diameter?
A PEEK shaft diameter can be held to +/-0.008 mm, and a specified precision feature to +/-0.005 mm. Call out the dimensions on the drawing; these values do not imply an h6 or H7 fit class.
How should the bore and outside diameter of a PEEK sleeve be referenced?
Define the bore, outside diameter, end face and rotary datum on the drawing, with separate coaxiality or runout requirements. This lets us check both the sleeve dimensions and their rotary relationship, rather than only one outside diameter.
Which PEEK grade should be specified for a sliding bushing at operating temperature?
Select the grade using operating temperature, load, speed, contact medium and fit requirements; these also affect running clearance. Provide operating conditions and a drawing for assessment. The PEEK name alone does not establish a usable temperature, clearance or service life.
Can every PEEK bushing in a batch be inspected, not just samples?
Yes. We can inspect critical fit dimensions and appearance on every part. Specify the dimensions for full inspection when ordering. A dimensional inspection report accompanies each batch.
How are thin-wall PEEK rings packed for international shipping?
Thin-wall rings are separated with foam and packed in cartons. Larger rings or batch orders can use wooden cases. Shipping options include DHL, FedEx, UPS and sea freight; we accept T/T, PayPal and Western Union.
Will you sign an NDA before reviewing our bushing drawings?
Yes. We can sign an NDA before you send the drawings. We accept STEP, IGES, STP, DWG or dimensioned PDF files, and can quote from 2D drawings alone.
Request a CNC Machining Quote from XCM CNC
Send us your drawings. Our team will review the file and reply with a machining quote. MOQ: 1 piece, with competitive low-cost pricing.



