
Custom PEEK CNC Turning and Milling Parts
Overview
PEEK turn-mill parts are often rotary components with threads, radial holes and anti-rotation flats. The side features must align with bores, outside diameters and end faces for assembly. XCM CNC machines these parts on a Mazak I-100S turn-mill center and DMG equipment. The factory holds ISO 9001, ISO 13485, IATF 16949 and GJB9001C certifications. PEEK’s chemical resistance, temperature resistance and rigidity can guide material selection, subject to the specified grade and operating conditions. MOQ is one piece. Prototypes typically take 3-7 days and standard orders 10-15 days.

Key Capabilities
Rotary surfaces and side features can be combined in PEEK turn-mill parts. The parameters below describe the turning, milling and threading capabilities covered here.
- Materials: PEEK, including unfilled, glass-filled, carbon-filled and wear-modified grades specified by drawing
- Tolerance: +/-0.005 mm on precision features; +/-0.008 mm for shaft diameters and locating holes
- Surface Finish: Turned diameters, bores and milled flats specified separately; finish requirements depend on PEEK grade and function, confirmed by order
- GD&T: Coaxiality, position and angular relationships referenced to rotary datums; verified on Hexagon CMM and TRIMOS 600L height gauge
- Max Size: Turning: up to diameter 1250 x 2000 mm; milling machine travel: 3000 x 1600 x 1400 mm. Combined-part size depends on geometry and setup
- Surface Treatment: Deburring; other treatment requirements reviewed for PEEK grade and drawing
- Thread: M2 to M220; NPT / BSP / G / PT pipe threads; thread depth up to 4 x D; go/no-go gauge inspection
- Precision Limit: +/-0.005 mm on precision features; +/-0.008 mm shaft diameter; slender shaft L/D 15:1; min. groove width 0.5 mm (specific features, by drawing review)

PEEK Turn-Mill Machining with Second Spindle
The Mazak I-100S turn-mill center has a second spindle, allowing front-side turning, back-side turning and lateral milling or drilling on one machine and reducing transfers between machines. In this process, shaft diameters can be held to +/-0.008 mm and specified precision features to +/-0.005 mm. Side-hole angular position and location are separate from size tolerance and should be specified against a rotary datum on the drawing.
PEEK CNC Turning Size Range for Shafts and Sleeves
PEEK turned parts can be machined up to diameter 1250 x 2000 mm. Jingshang 80 automatic lathes make small-diameter connectors and sleeves in batches. Slender shafts can reach L/D = 15:1. Because PEEK is less rigid than metal, long sections can deflect under the tool. A tailstock and staged finish turning are generally used to keep the outside diameter consistent.
PEEK Threaded Port Machining and Gauge Inspection
PEEK parts can have M2-M220 metric threads or NPT, BSP, G and PT pipe threads. Thread depth can reach 4 x D, with up to 50 mm effective depth in blind holes. Internal threads in plastic are recommended from M2 upward; smaller sizes are prone to thread damage. Functional threads are checked with go/no-go or thread ring gauges. Chips are cleared from thread roots before gauging to avoid a misleading go-gauge result.
PEEK Radial Holes, Grooves and Cross-Hole Deburring
The minimum drilled radial hole in a PEEK rotary part is 0.2 mm, and axial deep holes can reach L/D = 10. The minimum circlip or seal groove width is 0.5 mm; the minimum O-ring groove width is 1.0 mm. Intersections between side holes and main bores can be deburred. Specify internal edge and cleanliness requirements on the drawing. Leak testing is not included in the standard service.
Specifications
| Product Name | Custom PEEK CNC Turning and Milling Parts |
|---|---|
| Manufacturer | XCM CNC (Shenzhen Xinchuangmeng Co., Ltd) |
| Factory Location | Shenzhen, China |
| Quality System | ISO 9001, ISO 13485, IATF 16949, GJB9001C |
| Machining Process | CNC turning, turn-mill and milling |
| Material | PEEK |
| Material Grade | Unfilled, glass-filled, carbon-filled or wear-modified grade as specified by drawing |
| Tolerance | +/-0.005 mm on precision features; +/-0.008 mm for shaft diameters and locating holes |
| Surface Treatment | Deburring; other treatment by PEEK grade and drawing review |
| Max Part Size | Turning diameter 1250 x 2000 mm; milling 3000 x 1600 x 1400 mm |
| Inspection | Dimensional inspection report; CMM and FAI reports by order; equipment: Hexagon Inspector Classic 06.08.06, WanHao Rational VMS-3020G, TRIMOS 600L Height Gauge |
| Application | PEEK fluid connectors, guide sleeves, sensor seats and connector insulators |
| Key Features | Turned bores and diameters with milled side holes, flats, grooves or threaded ports; shaft and locating-hole sizes +/-0.008 mm; precision features +/-0.005 mm; threads: M2-M220; NPT / BSP / G / PT |
| Critical QC Requirements | Define rotary datums, side-hole position and angular relationship separately; deburring and inspection scope by order; surface finish: Turned and milled surfaces specified separately; requirements depend on PEEK grade and function |
| MOQ | 1 piece |
| Typical Lead Time | Prototype 3-7 days; standard 10-15 days depending on complexity and quantity |
| Drawing Formats | STEP, IGES, STP, DWG, PDF with dimensions |
Applications
Radial-port connectors for analytical instruments
Typical parts: Fluid connector, side-port valve body
PEEK for chemical-contact connectors can be assessed against the medium and material grade. Turning forms the outside diameter, thread and end face, while lateral milling and drilling form the radial port and its angular relationship to the rotary datum. Internal channels, medium and seal-validation requirements should be defined on the drawing.
Relevant capabilities: NPT / G pipe threads, minimum drilled hole 0.2 mm, cross-hole deburring.
Flatted guide sleeves for automation equipment
Typical parts: Flatted guide sleeve, sensor mount
PEEK can be evaluated where equipment parts need temperature resistance or electrical insulation. The turned profile defines the sleeve fit; milled flats, mounting faces or lateral locating holes set its orientation and connect the sensor.
Relevant capabilities: Shaft diameter +/-0.008 mm; back-side machining with the Mazak second spindle.
Slotted insulators for electronic connectors
Typical parts: Connector insulator, slotted spacer sleeve
A PEEK grade can be chosen to meet the electrical isolation target of an assembled structure. Turning forms the coaxial bore and outside diameter; milling adds an orientation slot or flat for connector assembly. Insulation performance depends on the grade data.
Relevant capabilities: Batch machining of small parts on Jingshang 80 automatic lathes; minimum groove width 0.5 mm.
Side-port instrument couplings and handle connectors
Typical parts: Instrument coupling sleeve, handle connector
PEEK can be assessed when an instrument accessory needs both cylindrical fits and a lateral passage. Combined turning and milling place the sleeve bore, thread, radial hole and flat in one component. The customer determines material grade, contact and cleanliness requirements from the drawing and applicable regulations.
Relevant capabilities: ISO 13485 quality system; internal threads from M2.
Threaded valve cores for fluid-control equipment
Typical parts: Threaded valve core, radial-port valve stem
Where fluid-control parts require media contact and rotary fits, a PEEK grade can be selected for the medium. After turning the shaft diameter, steps and threads, side holes or flats are milled and drilled to connect flow paths and drive elements. Define hole intersections and sealing edges on the drawing.
Relevant capabilities: Slender shafts up to L/D = 15:1; minimum O-ring groove width 1.0 mm.
Why Choose Us
Quality systems and turn-mill equipment
We machine under ISO 9001, ISO 13485, IATF 16949 and GJB9001C quality systems, using DMG, Mazak, Matsuura and Brother equipment. The Mazak I-100S turn-mill center has milling and drilling capability plus a second spindle for planning related operations.
Radial features referenced to rotary datums
For PEEK connectors with side holes or flats, we plan the outside diameter, bore, end face and side features together. Shaft and locating-hole sizes, tolerances and angular positions are confirmed separately on the drawing so the combined interface can be checked.
Tiered equipment strategy for cost-controlled machining
XCM CNC has four tiers of CNC equipment from mainland China, Taiwan, Japan, Europe and the United States. Less demanding turning and drilling operations go to domestic or Taiwanese machines, while precision turn-mill work goes to imported machines such as DMG and Mazak. Equipment is matched to actual precision needs to control cost while meeting the drawing.
Approved processes retained for repeat orders
After the first order is approved, we retain the operation sequence, fixtures and inspection items. These records can be reused for repeat orders without a new trial cut and help maintain consistency between batches.
One engineering contact from quote to delivery
The same engineer follows the quote, prototype and batch stages, so drawing revisions and technical questions do not need to be explained again. Customer drawings can be submitted after an NDA is signed.
FAQ
When does a PEEK part need both turning and milling?
Combined turning and milling suits a part with a fitted outside diameter or bore plus radial holes, flats or lateral mounting faces. Use of a turn-mill center and the operation sequence depend on geometry and drawing datums.
Can every PEEK turn-mill part be completed in one setup?
No. The Mazak I-100S second spindle can reduce reclamping for suitable geometries, but some parts still need multiple operations. The process depends on feature access and workholding requirements.
How should a radial hole be referenced to a turned bore?
Specify the rotary datum, radial-hole location and angular relationship, and identify the features to inspect. The +/-0.008 mm and +/-0.005 mm values are size tolerances; they do not automatically define hole position or angular accuracy.
Can you quote a PEEK part from a physical sample instead of a drawing?
Yes. We can make a custom part from a sample. Once it arrives, we measure critical dimensions and confirm tolerances and PEEK grade with you. If drawings are available, provide STEP, IGES, STP, DWG or a dimensioned PDF.
What documents are shipped with a PEEK turn-mill order?
Each batch includes a dimensional inspection report. Request CMM reports, first article inspection (FAI) reports and material certificates when ordering. Report formats can follow your template.
How long does it take to move from sample approval to batch production?
Prototypes typically take 3-7 days. After approval, standard batch lead time is 10-15 days, depending on geometry and quantity.
What payment, shipping and packaging options are available?
We accept T/T, PayPal and Western Union. Shipping options include DHL, FedEx, UPS and sea freight. Parts are packed with foam in cartons or wooden cases as required.
Request a CNC Machining Quote from XCM CNC
Send us your drawings. Our team will review the file and reply with a machining quote. MOQ: 1 piece, with competitive low-cost pricing.



